
Proceedings Paper
Large area LED packageFormat | Member Price | Non-Member Price |
---|---|---|
$17.00 | $21.00 |
Paper Abstract
Solid state lighting using LED-dies is a rapidly growing market. LED-dies with the needed increasing luminous flux per chip area produce a lot of heat. Therefore an appropriate thermal management is required for general lighting with LEDdies. One way to avoid overheating and shorter lifetime is the use of many small LED-dies on a large area heat sink (down to 70 μm edge length), so that heat can spread into a large area while at the same time light also appears on a larger area. The handling with such small LED-dies is very difficult because they are too small to be picked with common equipment. Therefore a new concept called collective transfer bonding using a temporary carrier chip was developed. A further benefit of this new technology is the high precision assembly as well as the plane parallel assembly of the LED-dies which is necessary for wire bonding. It has been shown that hundred functional LED-dies were transferred and soldered at the same time. After the assembly a cost effective established PCB-technology was applied to produce a large-area light source consisting of many small LED-dies and electrically connected on a PCB-substrate. The top contacts of the LED-dies were realized by laminating an adhesive copper sheet followed by LDI structuring as known from PCB-via-technology. This assembly can be completed by adding converting and light forming optical elements. In summary two technologies based on standard SMD and PCB technology have been developed for panel level LED packaging up to 610x 457 mm2 area size.
Paper Details
Date Published: 9 March 2015
PDF: 7 pages
Proc. SPIE 9383, Light-Emitting Diodes: Materials, Devices, and Applications for Solid State Lighting XIX, 93831A (9 March 2015); doi: 10.1117/12.2079380
Published in SPIE Proceedings Vol. 9383:
Light-Emitting Diodes: Materials, Devices, and Applications for Solid State Lighting XIX
Klaus P. Streubel; Heonsu Jeon; Li-Wei Tu; Martin Strassburg, Editor(s)
PDF: 7 pages
Proc. SPIE 9383, Light-Emitting Diodes: Materials, Devices, and Applications for Solid State Lighting XIX, 93831A (9 March 2015); doi: 10.1117/12.2079380
Show Author Affiliations
L. Goullon, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
R. Jordan, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
T. Braun, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
J. Bauer, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
R. Jordan, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
T. Braun, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
J. Bauer, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
Karl Friedrich Becker, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
M. Hutter, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
M. Schneider-Ramelow, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
K.-D. Lang, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
Technische Univ. Berlin
M. Hutter, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
M. Schneider-Ramelow, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
K.-D. Lang, Fraunhofer-Institut für Zuverlässigkeit und Mikrointegration (Germany)
Technische Univ. Berlin
Published in SPIE Proceedings Vol. 9383:
Light-Emitting Diodes: Materials, Devices, and Applications for Solid State Lighting XIX
Klaus P. Streubel; Heonsu Jeon; Li-Wei Tu; Martin Strassburg, Editor(s)
© SPIE. Terms of Use
