• Newsroom Home
  • Astronomy
  • Biomedical Optics & Medical Imaging
  • Defense & Security
  • Electronic Imaging & Signal Processing
  • Illumination & Displays
  • Lasers & Sources
  • Micro/Nano Lithography
  • Nanotechnology
  • Optical Design & Engineering
  • Optoelectronics & Communications
  • Remote Sensing
  • Sensing & Measurement
  • Solar & Alternative Energy
  • Sign up for Newsroom E-Alerts
  • Information for:
    Advertisers
SPIE Photonics West 2018 | Register Today

SPIE Defense + Commercial Sensing 2018 | Call for Papers

SPIE Photonics Europe 2018 | Call for Papers

SPIE Journals OPEN ACCESS

SPIE PRESS

SPIE PRESS

Print PageEmail PageView PDF

Lasers & Sources

High-energy large-aperture titanium:sapphire chirp-pulsed amplification laser system

A novel experimental setup can be used for the generation of 192.3J output energy (at a near-800nm wavelength), which can support a 5PW laser pulse output.
4 May 2017, SPIE Newsroom. DOI: 10.1117/2.1201612.006807

The chirp-pulsed amplification (CPA) technique involves stretching and compressing a laser pulse in the temporal domain before and after amplification.1 Since this technique was first proposed in 1985, it has been used to successfully solve the problem of how to achieve ultrashort laser pulse amplification.2 In addition, the development of mode-locking lasers—particularly the advent of the self-mode-lock titanium-sapphire (Ti:S) laser—has allowed the duration of ultrashort laser pulses to reach the femtosecond (fs) domain.3 Since the 1990s, the Ti:S/CPA technique has thus been used to rapidly develop ultra-intense and ultrashort lasers. Theoretically, the amplified output energy of such lasers can be greatly improved with the use of large-aperture Ti:S crystals. When larger-aperture Ti:S crystals are pumped at higher pump fluence and energy, however, the transverse amplified spontaneous emission (TASE) and parasitic lasing (PL) within the booster-amplifier volume are easier to suppress than the amplified pulse energy.4 This is the main barrier to realizing high-energy Ti:S/CPA amplifiers, even as Ti:S crystals with increasing diameters are produced.

Purchase SPIE Field Guide to LasersAt present, there are two main approaches to suppress transverse PL in these laser systems. First, the matched-index cladding (passive) technique can be used to increase the loss of spontaneous emission. In the second (active) technique, optimization of the time delay and lightly doped Ti:S crystals are used to control the transverse gain. To date, several countries have built petawatt-level ultra-intense and ultrashort laser systems (of which the focused intensity can be used to achieve 1021W/cm2) that are based on the Ti:S/CPA approach.5–7 Many research institutions around the world are also currently aiming to develop the first 10PW (i.e., 1015W) laser systems.8, 9

In this work,10 we have developed and experimentally demonstrated a new CPA experimental setup for the generation of near-200J pulse energy. The design of our system (see Figure 1) is based on a six-stage Ti:S CPA amplifier. Its structure is similar to a previous setup,7 but we have added a four-pass amplifier to enhance the energy stability. We use a lightly doped 150 × 46.7mm Ti:S crystal, with 92.6% small pump light absorption (from Crystal System Inc.) for the final amplification stage. The two-pump beam has a 15ns full width at half-maximum (and ∼26ns for the 1/e2 full width). The input seed is the output of an 80 × 32mm Ti:S amplifier (also from Crystal System) that has an energy of 35J. We also use a Cargille Series M refractive index liquid, doped with an absorber (IR 140) as the cladding material, to suppress the PL of the final amplifier. The two pump lines mean that we can amplify the 1053nm pulse to a maximum of 400J, with a 105mm beam in each channel. After the frequency doubling, the two pump beams are up-collimated to 120mm and are spatially filtered (where the image is relayed to the Ti:S crystal surface, with a maximum output energy of 190J at 527nm for each channel).


Figure 1. Schematic diagram of the chirp-pulse amplification (CPA) experimental setup. Ti:S: Titanium sapphire. CW-SLM: Continuous-wave single-longitudinal-mode. R.A: Regenerative amplifier. Δλ: Change in wavelength. amp: Amplifier.

A schematic diagram of the time delay between the two pump pulses in our final 150mm-diameter Ti:S amplifier is shown in Figure 2. We find that in the high-energy pumped large-diameter Ti:S amplifier, the output energy is sensitive to the time delay between the pump pulse and the seed pulse. By changing the optical distance of the two-pump line, we can achieve a time delay between the two pump pulses of about 11ns (approximately the time interval in the multipass amplifier). Furthermore, by subsequently carefully adjusting the time delay between the first pump pulse and the seed pulse, we can easily achieve an output energy of more than 180J (with an input energy of 35J) and finally obtain a maximum output energy as high as 192.3J in the lightly doped 150mm Ti:S amplifier.


Figure 2. Schematic sketch of the time delay (ΔT) between the two pump pulses.

Using these techniques, we measured the amplified output energy, with respect to the pump energy under optimized time-delay conditions. From our experimental results (see Figure 3), we confirm that both PL and TASE were effectively suppressed. In addition, we find that the output signal energy increases with pump energy. Indeed, we obtained a maximum amplified output energy of 192.3J at a pump energy of 312J.


Figure 3. Output of the final lightly doped Ti:S amplifier (as a function of pump energy), after optimization of the time delay.

We have also measured the output of the system when we use a heavily doped 157 × 27.2mm Ti:S crystal (with 95.3% small pump light absorption), but that has otherwise identical components. Even after optimizing the time delay for the heavily doped setup, we achieved an output of only 135.7J. Furthermore, the output ability of the lightly doped Ti:S is less sensitive to the seed-pump delay than the heavily doped crystal. Our results thus indicate that the lightly doped Ti:S crystal is more favorable for overcoming PL and TASE.

In summary, we have experimentally demonstrated the generation of an amplified output energy of 192.3J, and a conversion efficiency of 50%, with a 150mm-diameter Ti:S CPA amplifier. To the best of our knowledge, this is the first time that the 100J-level has been surpassed in a Ti:S laser system. If the compressed pulse duration can reach 27fs,10 the 5PW peak power of the output laser pulse can be realized. Our experimental results provide the basis for implementing larger-aperture Ti:S CPA laser systems with 10PW ultra-intense and ultrashort pulse output. In our recent and ongoing work we are enhancing the performance of the booster-amplifier and large-aperture pulse compressor even further. We have thus developed a novel temporal dual-pulse pumped technique for the suppression of PL and TASE. So far, we have obtained a maximum output energy of 202.8J with a compressed pulse duration of 24fs, as well as a throughput efficiency of 64% (which leads to a peak power of 5.4PW).

The authors are grateful to Lu Xu, Shuai Li, Yi Xu, Zhengzheng Liu, and Jun Lu for fruitful discussions, and to Dingjun Yin and Haihe Lu for technical support.


Zebiao Gan, Yuxi Chu, Xiaoyan Liang, Lianghong Yu, Cheng Wang, Yanqi Liu, Xiaoming Lu, Yuxin Leng, Ruxin Li, Zhizhan Xu
State Key Laboratory of High Field Laser Physics
Shanghai Institute of Optics and Fine Mechanics
Shanghai, China

References:
1. D. Strickland, G. Mourou, Compression of amplified chirped optical pulses, Opt. Commun. 56, p. 219-221, 1985.
2. M. D. Perry, D. Pennington, B. C. Stuart, G. Tietbohl, J. A. Britten, C. Brown, S. Herman, et al., Petawatt laser pulses, Opt. Lett. 24, p. 160-162, 1999.
3. U. Morgner, F. X. Kärtner, S. H. Cho, Y. Chen, H. A. Haus, J. G. Fujimoto, E. P. Ippen, V. Scheuer, G. Angelow, T. Tschudi, Sub-two-cycle pulses from a Kerr-lens mode-locked Ti:sapphire laser, Opt. Lett. 24, p. 411-413, 1999.
4. V. Yanovsky, K. Krushelnick, Influence of amplified spontaneous emission on gain lifetime in high-aperture Ti:sapphire amplifiers, Appl. Opt. 52, p. 2329-2331, 2013.
5. M. Aoyama, K. Yamakawa, Y. Akahane, J. Ma, N. Inoue, H. Ueda, H. Kiriyama, 0.85-PW, 33-fs Ti:sapphire laser, Opt. Lett. 28, p. 1594-1596, 2003.
6. T. J. Yu, S. K. Lee, J. H. Sung, J. W. Yoon, T. M. Jeong, J. Lee, Generation of high-contrast, 30 fs, 1.5 PW laser pulses from chirped-pulse amplification Ti:sapphire laser, Opt. Express 20, p. 10807-10815, 2012.
7. Y. Chu, X. Liang, L. Yu, Y. Xu, L. Xu, L. Ma, X. Lu, et al., High-contrast 2.0 petawatt Ti:sapphire laser system, Opt. Express 21, p. 29231-29239, 2013.
8. http://www.eli-beams.eu/science/lasers/ Information about the ELI laser system. Accessed 11 December 2016.
9. G. Chériaux, F. Giambruno, A. Fréneaux, F. Leconte, L. P. Ramirez, P. Georges, F. Druon, et al., Apollon-10P: status and implementation, Proc. AIP 1462, p. 78-83, 2012.
10. Y. Chu, Z. Gan, X. Liang, L. Yu, X. Lu, C. Wang, X. Wang, et al., High-energy large-aperture Ti:sapphire amplifier for 5 PW laser pulses, Opt Lett. 40, p. 5011-5014, 2015.