SPIE Digital Library Get updates from SPIE Newsroom
  • Newsroom Home
  • Astronomy
  • Biomedical Optics & Medical Imaging
  • Defense & Security
  • Electronic Imaging & Signal Processing
  • Illumination & Displays
  • Lasers & Sources
  • Micro/Nano Lithography
  • Nanotechnology
  • Optical Design & Engineering
  • Optoelectronics & Communications
  • Remote Sensing
  • Sensing & Measurement
  • Solar & Alternative Energy
  • Sign up for Newsroom E-Alerts
  • Information for:
OPIE 2017

OPIC 2017

SPIE Defense + Commercial Sensing 2017 | Register Today



Print PageEmail PageView PDF

Lasers & Sources

High-power fiber lasers for geothermal, oil, and gas industries

A high-power fiber laser succeeds in drilling through ultra-hard crystalline rock.
11 April 2014, SPIE Newsroom. DOI: 10.1117/2.1201403.005288

The concept of using lasers to drill through rock has been discussed in the oil and gas industries since the development of the high-power laser. Mauer's book on advanced drilling techniques summarized the early attempts to develop a CO2-based laser drill in the 1960s, but concluded that the technology was premature because of its size and complexity.1 In 2002, Ramona Graves from the Colorado School of Mines (CSM) demonstrated the potential of laser drilling by destroying a rock with a mid-IR advanced chemical laser, and later characterized the ability of a high-power diode laser to drill through rock.2 At the time, however, there were still substantial gaps in the technology that prevented commercial development. The innovation that opened up the prospect of commercializing laser drilling was the introduction of a 10kW fiber laser by IPG Photonics in 2008. A year later, with the assistance of CSM, we started developing a laser drilling process capable of creating a commercial grade borehole, along with the supporting technology necessary to field a laser drilling system.

Purchase SPIE Field Guide to LasersThe first major advance in the drilling industry was the invention of a twin-roller-cutter drill bit by Howard Hughes in 1908.3 The drill bit revolutionized the drilling industry and allowed the Hughes Tool Company to dominate the drill bit market. The original concept of a twin roller was improved upon by a researcher at the Hughes Tool Company and resulted in the introduction of the tri-cone bit 24 years later, which has been the workhorse of the drilling industry for the last 80 years. The next advance in drilling technology was the introduction of the polycrystalline diamond compact (PDC) bit by General Electric in 1971. Over the last 30 years, this bit has proven to be more reliable than the tri-cone bit in certain rock types.4 As a result, the PDC bit has overtaken the tri-cone bit as the market leader in recent years. However, both bits still struggle with ultra-hard crystalline rocks such as dolomite, basalt, and granite. We have developed a new type of drilling system that combines a precision heat source with a PDC bit, and we have shown it to be more effective at drilling rocks with compressive strengths exceeding 30ksi than either a conventional tri-cone bit or a PDC bit (see Figure 1).

Figure 1. A drill bit that combines high-power laser energy with polycrystalline diamond compact bit technology.

Our drill bit features a rotating laser beam that fractures and weakens the rock, combined with a set of PDC cutters that scrape the weakened rock from the area that is exposed to the laser beam.5, 6 The laser energy that exits the drill bit creates a unique pattern on the rock that is rotated—much like a radar sweep—to heat up the bottom surface of the borehole (see Figure 1). The laser effectively spalls the surface of the rock, and in doing so introduces microfractures that enable easy removal of the layer of fractured rock. Since the strength of the rock is reduced from its >30ksi compressive strength to less than a few hundred psi during this process, it takes very little mechanical energy to ultimately remove the rock. For example, a conventional tri-cone bit requires over 25,000lbs of weight on the bit to penetrate rock with >30ksi compressive strength. Our drill bit is capable of penetrating the same rock at 2–3× the rate of penetration, but with less then 1500lbs of weight on bit while being rotated with less than 100ft-lbs of torque and using less than 10hp during the drilling process. We have successfully drilled through all of the rocks found in oil, gas, and geothermal applications with 4, 6, and 8.5” diameter bits. We have also successfully integrated the laser drill into a drilling rig and demonstrated boring a 12' hole through dolomite with a compressive strength of 30ksi (see Figure 2).

Figure 2. A test hole drilled 12' deep in dolomite rock with a compressive strength exceeding 30ksi. The discoloration of the rock is oil discarded by the drilling motor.

The goal of this work was to demonstrate improved speeds for drilling through ultra-hard crystalline rock compared to a conventional drilling system, which in turn reduces the cost of drilling geothermal wells. With our partners the Department of Energy's Advanced Research Projects Agency - Energy (ARPA-E) and CSM, we have demonstrated a laser-based drilling process with a faster rate of penetration (2–3×) and substantial decrease in the weight on bit (>25×) that ultimately leads to a longer bit lifetime. Our next step is to perform drilling tests at higher power levels to characterize the scalability of the drilling process.

This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any agency thereof. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government or any agency thereof.

Mark Zediker
Foro Energy
Littleton, CO

Mark Zediker gained his PhD from the University of Illinois in 1984 and worked at McDonnell Douglas from 1983 to 1998 on high-power laser systems. He founded Nuvonyx in 1998 to bring high-power diode laser technology to the industrial marketplace, before co-founding Foro Energy in 2009 to develop high-power laser applications in the geothermal, oil, and gas industries.

1. W. C. Mauer, Advanced Drilling Techniques, Petroleum Publishing Company, 1980.
2. R. M. Graves, Comparison of specific energy between drilling with high power lasers and other drilling methods, SPE Ann. Tech. Conf. Exhibitions, 2002. doi:10.2118/77627-MS
3. H. Hughes, Machine for cutting large pipe, US Patent 930,755, 1908.
4. D. E. Scott, The history and impact of synthetic diamond cutters and diamond enhanced inserts on the oil and gas industry, Int'l Industrial Diamond Conf., p. 1-33, 2005.
5. M. Zediker, B. Faircloth, D. Grubb, S. Kolachalam, S. Schroit, C. Rinzler, W. Gray, et al., High power lasers for rock drilling, Proc. Swissphoton. Wrkshp. Photon. Deep Geothermal Energy Harvest., p. 39-42, 2012.
6. M. Zediker, High power fiber lasers in geothermal, oil and gas, Proc. SPIE 8961, p. 89610D, 2014. doi:10.1117/12.2042339