SPIE Startup Challenge 2015 Founding Partner - JENOPTIK Get updates from SPIE Newsroom
  • Newsroom Home
  • Astronomy
  • Biomedical Optics & Medical Imaging
  • Defense & Security
  • Electronic Imaging & Signal Processing
  • Illumination & Displays
  • Lasers & Sources
  • Micro/Nano Lithography
  • Nanotechnology
  • Optical Design & Engineering
  • Optoelectronics & Communications
  • Remote Sensing
  • Sensing & Measurement
  • Solar & Alternative Energy
  • Sign up for Newsroom E-Alerts
  • Information for:

SPIE Photonics West 2017 | Register Today

SPIE Defense + Commercial Sensing 2017 | Call for Papers

Get Down (loaded) - SPIE Journals OPEN ACCESS


Print PageEmail PageView PDF

Optoelectronics & Communications

Optical beamforming for communication and power transmission

A spatial light modulator focuses and modulates LED light to improve data rate and transmission distance and also deliver wireless power.
6 February 2014, SPIE Newsroom. DOI: 10.1117/2.1201402.005283

In recent years, the superior efficiency of LED lights has made them popular replacements for indoor incandescent lightbulbs and fluorescent lamps. LEDs also have the advantage that their light output can be modulated with high-frequency signals. As a result they can also be used for ‘visible light communication’ (VLC): see Figure 1.1–3

VLC has gained much attention as a strong candidate for future indoor wireless communication because it has several advantages over conventional radio frequency (RF) wireless communications.1 First, visible light can be used freely for VLC applications, whereas most radio frequencies are regulated by government. Second, the potential communication bandwidth of visible light is incomparably wider (∼400THz) than conventional Wi-Fi bandwidth (100MHz). Third, light is easily blocked by a wall. Consequently, communication security can easily be maintained between rooms. And finally, we can easily see whether the LED and hence the VLC system is on or off.

Figure 1. Concept of visible light communication (VLC).

However, VLC data rate and transmission distance performance have not yet surpassed existing Wi-Fi technology,4 and this is a barrier to the spread of VLC. The data rate has been limited mostly by the limited modulation bandwidth of LED devices, and transmission distance has been limited mostly by the rate of decline in irradiance with distance.

To address this, colleagues and I have proposed and demonstrated improved VLC technology based on ‘optical beamforming,’1 which focuses LED light on a desired target (see Figure 2). This technique does not depend on the electrical signal format, and thus can be widely used. It enhances the data rate of the VLC by raising the signal-to-noise ratio (SNR) of the received signal sufficiently for high-level quadrature amplitude modulation. It also enhances the transmission distance by raising the signal strength itself.

Figure 2. Concept of optical beamforming.

To demonstrate the proposed VLC technology, we used a spatial light modulator (SLM) to focus LED light on the desired target (see Figure 3). The SLM modulates the phase or amplitude of light on each pixel, and operates as a dynamic diffractive element controlled by electrical signals.5 We found that the transmission distance of the signal almost doubled1 and the SNR of the received signal increased by 12dB with optical beamforming (see Figure 4). We have also suggested an automatic location-detecting algorithm, based on ‘direction code.’ Using the communication algorithm, we can focus on moving devices.1

Figure 3. Experimental setup of VLC with optical beamforming. SLM: Spatial light modulator.

Figure 4. Eye diagram of the received signal (a) before optical beamforming and (b) after optical beamforming. The open space after optical beamforming indicates a higher signal-to-noise ratio.

We have also used optical beamforming to demonstrate a new wireless optical power transmission technology.6 Wireless power transmission has recently attracted substantial research interest.7, 8 Most previous work is based on magnetic resonance, induction coupling, or RF electromagnetic waves, but these methods have several weaknesses. Induction coupling has a very short (less than several centimeters) transmission range. Magnetic resonance is difficult to maintain in a dynamic real field. It is also challenging for a single transmitter to meet resonance conditions for several target devices simultaneously.

To overcome these problems, we used visible light to transfer power. The technology consists of three parts: an optical source, an optical beamforming device to focus the light on a target device, and a solar cell to receive the optical power. It has the advantages of a longer transmission distance, automatic accurate targeting capability, and the ability to transmit power even to a moving device with a proper communication protocol. Our experimental result showed a power transmission efficiency of 1.3%, including electric-to-optic conversion efficiency in an LED and vice versa in a solar cell.6

In summary, we have used an SLM to modulate the phase or amplitude of each pixel of LED light so that it operates as a dynamic diffractive element controlled by electrical signals. Using a communication algorithm, the resulting optical beamforming can also be applied to moving devices. In this way, we have demonstrated significant improvement in the data rate, transmission distance, and SNR of VLC. We have also achieved power transmission efficiency of 1.3% using an LED, SLM, and solar cell. However, we expect that more than 20% power transmission efficiency may be possible in the future. We are now working to achieve this.

We are grateful for support from Basic Science Research Programs through the National Research Foundation of Korea (NRF) funded by the Ministry of Education, Science, and Technology (NRF-2010-0022318 and NRF-2012M3C1A1048865).

Sung-Man Kim
Department of Electronic Engineering
Kyungsung University
Busan, Republic of Korea

Sung-Man Kim is a faculty member. He is also currently chair of the optical communication and wireless communication division of the Korea Institute of Electronic Communication Sciences.

1. S.-M. Kim, S.-M. Kim, Wireless visible light communication technology using optical beamforming, Opt. Eng. 52(10), p. 106101, 2013. doi:10.1117/1.OE.52.10.106101
2. H. Haas, High-speed wireless networking using visible light, SPIE Newsroom, 2013. doi:10.1117/2.1201304.004773
3. S. Rajagopal, R. D. Roberts, S.-K. Lim, IEEE 802.15.7 visible light communication: modulation schemes and dimming support, IEEE Commun. Mag. 50(3), p. 72-82, 2012.
4. K.-D. Langer, J. Hilt, D. Schulz, F. Lassak, F. Hartlieb, C. Kottke, L. Grobe, V. Jungnickel, A. Paraskevopoulos, Rate-adaptive visible light communication at 500Mb/s arrives at plug and play, SPIE Newsroom, 2013. doi:10.1117/2.1201311.005196
5. J. Reményi, P. Várhegyi, L. Domján, P. Koppa, E. Lõrincz, Amplitude, phase, and hybrid ternary modulation modes of a twisted-nematic liquid-crystal display at ∼400nm, Appl. Opt. 42(17), p. 3428-3434, 2003. doi:10.1364/AO.42.003428
6. S.-M. Kim, S.-M. Kim, Wireless optical energy transmission using optical beamforming, Opt. Eng. 52(4), p. 043205, 2013. doi:10.1117/1.OE.52.4.043205
7. A. Kurs, A. Karalis, R. Moffatt, J. D. Joannopoulos, P. Fisher, M. Soljacic, Wireless power transfer via strongly coupled magnetic resonances, Science 317, p. 83-86, 2007.
8. W. Stewart, The power to set you free, Science 317, p. 55-56, 2007.