SPIE Membership Get updates from SPIE Newsroom
  • Newsroom Home
  • Astronomy
  • Biomedical Optics & Medical Imaging
  • Defense & Security
  • Electronic Imaging & Signal Processing
  • Illumination & Displays
  • Lasers & Sources
  • Micro/Nano Lithography
  • Nanotechnology
  • Optical Design & Engineering
  • Optoelectronics & Communications
  • Remote Sensing
  • Sensing & Measurement
  • Solar & Alternative Energy
  • Sign up for Newsroom E-Alerts
  • Information for:
SPIE Photonics West 2019 | Call for Papers

2018 SPIE Optics + Photonics | Register Today



Print PageEmail PageView PDF

Lasers & Sources

Blue and IR alkali lasers pumped by multiphoton absorption

Red pumping produces both blue and mid-IR beams without resonator or thermal load, offering enhanced underwater communication and blinding heat-seeking missiles.
24 February 2010, SPIE Newsroom. DOI: 10.1117/2.1201002.002558

A new class of diode-pumped laser based on excitation of the D2hyperfine-transition line in alkali atoms and subsequent lasing on the D1 line is currently receiving considerable attention.1 Diode-pumped alkali lasers (DPALs) have been demonstrated in rubidium (Rb) and cesium (Cs) at 17 and 48W with 53 and 52% slope efficiency, respectively.2,3 They require high buffer-gas pressures to match the width of the absorption profile to the laser's spectral line shape, and a collision partner such as ethane to relax the electron population in the pumped level to the upper laser.

While a few groups have extended and adapted these alkali systems to operate at shorter wavelengths, such schemes require pumping with two distinct light sources. For example, two low-power continuous-wave diode lasers operating at 852 and 917nm yield an ~4μW blue beam at 455nm.4 Lasing without inversion has also been demonstrated in Rb based on both V-type and sequential double-resonance processes.5–8 In the latter experiment, two 20mW lasers at 780 and 776nm produce a blue beam with a power of up to 40μW.6 Such sources might find application in laser communications through water. However, the two-wavelength pump requirement adds complexity to the system.

Figure 1. Energy-level diagram and lasing mechanism for rubidium (Rb).

We have produced a blue beam using a single far-red laser tuned to the two-photon absorption excitation of the 2D3/2, 5/2 and excited 2S1/2 states in Rb and Cs. Lasing is simultaneously achieved at mid-IR and blue wavelengths after excitation in the red through the processes illustrated in Figure 1. The system operates at low pressure without collisional energy transfer, offering minimal heat load, and requires only a single pump source. The conversion efficiency at blue wavelengths is about 0.4%, exceeding that achieved in double-resonance experiments. We also achieved several mid-IR lasing transitions in the 2–5μm atmospheric-transmission window.

We observed a blue beam, accompanied by a dispersed red pump-laser spot, when tuning a pulsed dye laser through the two-photon absorption wavelengths in both Rb and Cs (see Figure 2). The threshold is modest (~0.3mJ/pulse for Rb). Slope efficiencies increase dramatically with higher alkali concentrations and peak at 0.4%. We achieved almost 10μJ/pulse or 0.1mW average power for the Cs system. The spectral width of the absorption feature is about 25 times smaller than the pump bandwidth, and only a few percent of the incident pump energy is absorbed. The slope efficiency (based on absorbed photons) exceeds 3%.

Figure 2. Dispersed beams for the Cs cell in the forward direction.

To confirm that the alkali atoms were pumped by two-photon absorption, we obtained an excitation spectrum based on blue stimulated emission (see Figure 3). The blue spots for Rb occurred at pump wavelengths of 778.1, 778.2, and 760.1nm, corresponding to the 52S1/2 to 52D3/2, 52D5/2, and 72S1/2 transitions, respectively. A small leakage of the pump beam through the blue bandpass filter produces the baseline intensity, and increased absorption at the D2 spectral feature is evident.

Figure 3. Rb laser-excitation spectrum for a cell at a temperature of 217°C. λ: Wavelength.

The intensity of the IR beam increased linearly with pump energy to 100mJ, with a very small threshold. Given the minimal delay between the pump pulse and the appearance of the blue beam, it appears that stimulated emission on IR transitions is required to complete the three-step cycle. In Cs, the IR transitions range between 1.94 and 2.43μm and in Rb at 3.85–5.2μm.

In summary, we have achieved stimulated emission on the blue atomic transitions in Rb and Cs by pumping at a single wavelength. The slope efficiency of 0.4% in Rb is considerably higher than that achieved in sequential double-resonance experiments. Incomplete (10%) absorption of pump photons is an important contributor to the decreased efficiency and might be improved with narrow-band pumping or pressure broadening. Cascade lasing on IR lines followed by blue transitions does not lead to quantum defects, offers the potential for low heat loads, and does not require spin-orbit-coupling gas. The latter has caused soot buildup problems in traditional DPAL cells. It appears that the performance of our new system can be enhanced by scaling to higher alkali concentrations, possibly in a heat-pipe configuration. Threshold pump intensities are high, but we have not assessed the ultimate performance limits of this system. We will next perform a full analysis of the kinetic mechanism to evaluate both the system's scaling and efficiency.

Glen Perram
Air Force Institute of Technology
Wright-Patterson Air Force Base (AFB), OH

Glen Perram has been a faculty member at the Air Force Institute of Technology since 1989. His research interests include high-energy lasers and remote sensing of battlespace combustion events.

Clifford Sulham, Greg Pitz
Department of Engineering Physics
Air Force Institute of Technology
Wright-Patterson AFB, OH

Clifford Sulham and Greg Pitz are PhD candidates in applied physics.