SPIE Digital Library Get updates from SPIE Newsroom
  • Newsroom Home
  • Astronomy
  • Biomedical Optics & Medical Imaging
  • Defense & Security
  • Electronic Imaging & Signal Processing
  • Illumination & Displays
  • Lasers & Sources
  • Micro/Nano Lithography
  • Nanotechnology
  • Optical Design & Engineering
  • Optoelectronics & Communications
  • Remote Sensing
  • Sensing & Measurement
  • Solar & Alternative Energy
  • Sign up for Newsroom E-Alerts
  • Information for:
    Advertisers
SPIE Photonics West 2017 | Register Today

SPIE Defense + Commercial Sensing 2017 | Call for Papers

Journal of Medical Imaging | Learn more

SPIE PRESS




Print PageEmail PageView PDF

Biomedical Optics & Medical Imaging

Designing remotely activated microvalves for biomedical applications

RF-controlled battery-less microvalves are fabricated on a biocompatible substrate that allows for communication and remote actuation.
5 March 2007, SPIE Newsroom. DOI: 10.1117/2.1200702.0688

A number of microscopic valve structures have been developed that are based on silicon and use an energy source that is directly connected to the device.1,2 These are appropriate for many uses, but not for biomedical applications. On the other hand, some researchers have addressed the possibility of using biomedical implants for biotelemetry applications.3 If these devices are to be implanted in an animal or a human body, we need to find a way to make them both biocompatible and remotely actuated. Size, weight, complexity, and security must all be addressed.

The shorter the microwave signal frequency, the shorter the penetration depth through water-containing tissues. Therefore, we'd like to find the optimal tradeoff between the interrogation signal frequency and microvalve size.4,5 Microvalve applications usually require small size and low weight, which creates an upper limit on the antenna size.

Also, we would like to have a microvalve that doesn't incorporate a battery, both because this would decrease the size and weight of the valve and because it would eliminate battery-replacement requirements. An additional disadvantage of powering the devices by a battery or a capacitor—charged using inductive coupling—for short-term burst operation4,5 is that these schemes require active microelectronics to be integrated with the microvalve. In contrast, we propose using a piezoelectric polymer material with no active microelectronic components.6,7 This allows the integration of the antenna, interdigital transducer (IDT), surface acoustic wave (SAW) device, and actuator to control the microvalve without batteries on a biocompatible substrate (see Figure 1).

 
Figure 1. An implanted microvalve uses interdigital transducers (IDTs) and a microannetenna to establish a secure wireless connection to exterior devices. Power from the RF pulses is transferred from the surface-acoustic-wave (SAW) device to the micro-actuator to open and close the microvalve.

We have developed four microvalve structures. Two of them use a bimorph actuation mechanism (see Figure 2), while the others use unimorph actuation. These structures were modeled using simulation tools from ANSYS, Inc.7 We also conducted modeling of water-based microfluidic structures to demonstrate a high flow rate. Our modeling shows that the bimorph actuation has a higher flow rate than the unimorph structure.6,7 We are currently comparing these results to other structures published in the literature.


Figure 2. A bimorph microvalve structure in which the valve is normally closed. (1) Side view of the structure shows the path of the fluid flow when the valve is open. (2) Top view of the structure. When the valve is interrogated by a coded RF signal, the bimorph cantilever—made of a piezoelectric material—bends downward, allowing liquid to flow from the inlet to the outlet.

Because of the wireless nature of the device we investigated improving the security of the microvalve by developing coding techniques to ensure activation only when a coded RF signal matches an embedded code in the microvalve. We have demonstrated that secure actuation of a microvalve is possible using SAW-device-based IDT structure with variable code length. Our modeling shows it is possible to achieve such actuation by using SAW correlator in conjunction with the developed microvalve structure.8,9 We have demonstrated the use of Barker, maximum length sequence (MLS), and Golay codes for unique activation of the microvalve with a high signal-to-noise ratio. The binary weighted Barker code was found to provide the highest processing gain needed for a unique activation.7

We propose using microvalve structures in a number of medical applications: for cancer chemotherapy, the device could provide a higher concentration of the drug dose in certain areas; for hormonal treatments, the device can apply well-controlled doses; and for flow cytometry, a microvalve could be used to sort microscopic particles suspended in a stream of fluid.3

The mechanical coupling efficiency in the SAW correlator is low, which reduces its output voltage, which results in less voltage available to actuate the microvalve. We are now looking into the use of floating-electrode type unidirectional transducer to improve the mechanical coupling efficiency. Also we are currently investigating a number of techniques to miniaturize the antenna size including dielectric loading, slow-wave structural patterns on the radiating element, and either capacitive or inductive loading. Also, we are looking into fabricating the proposed microvalves to evaluate their performance. A further extension of the project is to develop a micropump using a piezoelectric diaphragm that is synchronized with the actuator for independent operation.

The authors would like to acknowledge support from both The Australian Research Council (ARC) and the faculty of Faculty of Engineering, Computer & Mathematical Sciences for sponsoring this project. We also acknowledge useful discussions with both Ajay Tikka and Derek Abbott from the School of Electrical and Electronic Engineering.


Don Dissanayake and Said Al-Sarawi 
The Centre for High Performance Integrated Technologies and Systems (CHiPTec), University of Adelaide
Adelaide, Australia 

Don Disaanayake started his postgraduate studies at CHiPTec on March 2006 and his research is on Microelectronics and MEMS. He received his bachelors in Computer Systems Engineering from the University of Adelaide in 2004.

Said Al-Sarawi completed his PhD from the School of Electrical and Electronic Engineering, University of Adelaide, in 2003. His research interests are high-speed data converters using CMOS and optoelectronics technologies, radio frequency identification systems (RFID), and mixed signal design for biomedical applications.